Frequency Range

47-63Hz

Input Current(Maximum value)

Full load 3000W output, use 220VAC input 16A

Full load 2500W output, use 110VAC input 26A
(When using 110V input, the maximum power is limited to 2500W)

Power during standby

10W

Power factor

(PF value)

Use the 220VAC input and power 100% full load,Power factor ≥ 0.96 (refer to PF value in the figure below)

Use the 110VAC input and power 100% full load,Power factor ≥ 0.97 (refer to PF value in the figure below)

Input Wiring method

3PIN KF78 spacing 14mm PCB fence type wiring terminal with protective cover

Enter a surge current

Cold start 220VAC/53A, 110VAC/28A

DC output voltage

24VDC

36VDC

48VDC

60VDC

72VDC

110VDC

220VAC Input

Output current

125A

83.3A

62.5A

50A

41.6A

27.2A

Output Power

3000W

3000W

3000W

3000W

3000W

3000W

Efficiency

89%

91.2%

91.8%

92%

92.3%

93.2%

110VAC Input

Output current

104A

69.4A

52A

41.6A

34.7A

22.7A

Output Power

2500W

2500W

2500W

2500W

2500W

2500W

Efficiency

87.2%

89.3%

89.6%

90.3%

91.4%

91.5%

Tip: When using the AC110V input, Need to reduce the output power to 2500W

Ripple (max)

160mv

200mv

220mv

260mv

280mv

330mv

Voltage regulation range

17-24V

26-36V

33-48V

42-60V

48-72V

74-110V

Linear adjustment rate

±0.5%

±0.5%

±0.5%

±0.5%

±0.5%

±0.5%

Load Regulation

±0.5%

±0.5%

±0.5%

±0.5%

±0.5%

±0.5%

Voltage accuracy

±2%

±2%

±2%

±2%

±2%

±2%

Start / rise time

Power-on post-delay 3-4 second start/ 500MS voltage complete

Power-off keeping time

16ms(220VAC  80% load )    8ms(220VAC  100% load )

Output wiring method

Copper strip terminal, M5 nut seat，Need to use a power supporting copper terminal wiring

1. Efficiency This parameter is measured under 100% full load conditions, the efficiency is not a constant value (refer to the following efficiency VS load graph)

2. Wave and noise measurement Method: Use 12 "twisted pair, output terminal parallel 0.1uf and 47uf capacitors,  the oscilloscope bandwidth is limited to 20 MHz.

Output voltage regulation

Output voltage adjustable, Adj-V potentiometer manually adjustment )

Output current adjustment

The output current can be adjusted, the ADJ-A potentiometer manually adjusts, when the load reaches the current setting value, the constant current output (output current remains unchanged, the output voltage is reduced with the load)

Auxiliary voltage output

This machine provides a 12V-300mA auxiliary voltage output

PWM

Staggered parallel Two-transistor forword

Output short circuit protection

There is no output after the output is shorted, and the output voltage is automatically restored after short circuit release.

Output overload protection

The overload protection mode is constant current limit mode, the lock output current value is unchanged,

and the output voltage is increased and decreases with the load.

Overheating protection

When the heat sink temperature of the PWM transistor reaches 85 ° C ± 5%, the output voltage is turned off.

Automatic recovery when the temperature drops to 75 ° C ± 5%

Insulation resistance

I/P-O/P,I/P-FG,0/P-FG:100M Ohms /500VDC /25℃/70%RH

Leakage current

≤2MA/AC220V

Withstand voltage

Input and output :3000VAC     Input and ground :1500VAC       Output end and housing:500VAC

Storage temperature, humidity

-40~+55℃，20-90%RH

Altitude

Only used in 2500m altitude

Fan noise value

In a quiet indoor environment of 20-30dB, when the fan rotates at the highest speed, the measured value at 1 meter from the power supply is 55dB

Shell size

294mm long (45mm extension outside the terminal) * Width 185mm * height 65mm     

Install fixing hole

(Horizontal installation) length spacing: 236mm  width spacing: 205mm (reference dimension)

Net/Gross weight

3.5KG/4KG

Warning

1. Pay attention to ventilation and heat, can not be installed inside the full sealed box

2. This power supply is limited to indoor use, no rain, no waterproof, no dust, not suitable for outdoor environment and harsh environments